Ford Focus ST Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 21 Results
  1. Focus ST Mk3 Non Technical Discussion
    Don't know if anyones come across this but i noticed my ecu box has come loose, just concerned about water getting in it, does it perhaps just need some new fixings to hold in place.
  2. Mk2 Miscellaneous
    After changing clocks, ECU, Keys and fusebox module the u1900-60 error is still popping up. i have checked all wires leading from the ECU to the fuse box to the cluster and cant seem to find a bad wire anywhere? not sure if it any help but when the battery started to die at 9.6V the error...
  3. Mk3 ECU Remapping & Software
    Hi guys any help here would be appreciated Changed the R9DA engine in my pfl mk3 st All plugged in ready to go and I get ignition lights and it was clicking in the fuse box However I checked all the fuses and earths etc the usual and now its coming up with engine malfunction , service now...
  4. Mk2 Lighting & Electrical
    Hi guys, just wondering if anyone has replaced the ecu in their keyless MK2 FL ST225? Is it similar to doing the keyed MK2 PFL? I got a wreck and it runs a map. I'll fit the mods in my car and considering swapping out the stock mapped ecu in my car. This of course will maroon my car on the map...
  5. Mk2 Engine, Exhaust and Induction
    Hi All, I have a RS ECU holder for my st225 but I cant seem to find the rubber bung mounts that it slots into off the block. Does anyone know where I can find them Kind Regards
  6. Mk2 ECU Remapping, Software & Tuning Packages
    Hi, I've tried three different ELM327 based devices which I am led to believe 'should' work but none of them can connect to the ECU. One of them is a handheld and the other two are Bluetooth which connect to my tablet via an app like Torque Pro. Both worked fine on two previous Fords I had...
  7. Mk2 ECU Remapping, Software & Tuning Packages
    Hi folks, After reading a previous thread on here from 2012, Im taking my car to Ford (Clevedon) to get a suspected remap removed. Ive only owned it for a few weeks but it doesnt drive right and all symptoms point towards a remap. I want the car as standard as possible for the moment, and if...
  8. Mk2 ECU Remapping, Software & Tuning Packages
    Has anyone ever heard of a fried ECU on an ST. I dont know if people seen my other post but do you think that my ECU could have been killed by a faulty diode in an alternator. Its got a new Battery, New Alternator, Checked fuses, Checked earth leads and are all ok and a Repaired dash cluster...
  9. Focus ST Mk2 Non Technical Discussion
    Hi guys, Can anyone provide me with a price for the RS ECU Holder to fit my ST 225?
  10. Mk3 ECU Remapping & Software
    Hi, Hope I've posted this in the right section... Does anyone have an idea how much import charges will cost me to get a Cobb Accessport from the States and also point me in the right direction, from which company would be best to buy from? Thanks
  11. Focus ST Mk2 Non Technical Discussion
    Hi just done a diagnostic test on my st a got a fault code Type m P1260-21 Does anyone know what this is thanks
    ecu
  12. Mk3 ECU Remapping & Software
    Hi everyone, I'm looking at the various tuning options at the moment and am leaning towards Bluefin with an Airtec Intercooler. Is this any good? Would any of you suggest a sports-cat and exhaust too, or leave as standard? ( the only thing that puts me off aftermarket exhausts is the drone you...
  13. Mk2 ECU Remapping, Software & Tuning Packages
    Hi guys! Was thinking about getting my car mapped this weekend, just the base map for now. I'm planning on a uprated intercooler and induction kit (already have scropion cat back and K&N Panel) later this year along with a more aggressive map But my question for now is, Should i get a bluefin...
  14. Mk2 Engine, Exhaust and Induction
    Hello All, It would appear that I have some fault codes, and I'm wondering if anybody could assist with diagnosis and repair. P0183-A1 - Fuel Rail Pressure Sensor A Circuit High P0190-24 - Fuel Rail Pressure Sensor I cleared the codes and went for a couple mile spirited drive with no loss of...
  15. Project Threads
    Hey people, Being a skilled sheetmetal worker I thought it was about time I put my skills to use and make a ECU cover. I didn't like the idea of the cars brain (so to speak) being open to the elements since I've cut two big gaping holes in the bonnet and fit RS vents, which I'm sure most of you...
  16. Ford Parts, Accessories and FINIS Codes
    Hey people, Being a skilled sheet metal worker I thought it was about time I put my skills to use and make a ECU cover. I didn't like the idea of the cars brain (so to speak) being open to the elements since I've cut two big gaping holes in the bonnet and fitted RS vents, which I'm sure most of...
  17. Project Threads
    Finally finished my ECU mount/covet, made mainly out of the original airbox plus other bits and bobs It was alot of work and all because i couldnt afford an rs ecu mount i'll let the pics do the the talking, but im pretty pleased with it "HOW TO" tools: saw, stanley knife, drill, super...
    ecu
  18. Mk2 ECU Remapping, Software & Tuning Packages
    My car is booked in to Arnold shark to get 2nd service and not(stupidly took option when bought)but I'm wondering should I return car to stoc or leave remap on it just wondering as they sent card through post about updating software although I have latest on it
  19. Mk2 ECU Remapping, Software & Tuning Packages
    Hi Peeps, As the title states what is the current reset cost if I was to buy a second hand Bluefin Unit? Cheers Mark
1-19 of 21 Results
Top